You want to clean an old motorcycle engine but looking at the tutorials that how to best clean up an old motorcycle engine. It’s essential to Clean up an old motorcycle engine to make your bike look good. And also to save your motorcycle engine if you are not cleaning the engine you may face some issues.
But come again if you clean your motorcycle it will save you money which you can use in other things you may go to the professional shop and ultimately they will charge you a big amount of money so here we explain to you in a very beautiful way that how you can clean up an old motorcycle engine so follow and get the things done.
Table of Contents
What will be needed in order to clean up an old motorcycle engine?
There are a lot of products which you can use in order to clean up an old motorcycle engine but we list a few of that which you can take a look into it:
- A soft brush with small bristles
- Automobile blow dryer
- Air nozzle
- Paraffin
- Use detergent to warm the water
- Chrome polish
- A plastic bag
- Use a citrus-based degreaser (orange or lemon)
- Air compressor and air hose/ automotive blow-dry
- Masking tape
- Dry towels
- High-pressure water hose and spray nozzle preferred
- Rubber seal protector
Follow the next Steps Inorder to do Proper cleaning of your old motorcycle engine
Step 1 - do Used compressed air, and blow out dust
At first, used compressed air to remove the dust from the engine as much as you can and then next
Step 2 - De-grease engine areas with a degreaser
After protecting the sensitive parts with plastic, then pick the citrus-based degreasing agent and spray it on the motorcycle engine. And then follow the product manufacturer guide. And make sure that you set the degreasing agent for a good amount of time in some cases you should let the degreaser for 20-35 minutes
Step 3 - Rinse the degreaser off
The upcoming step is to take the water pipe and a high-pressure spray nozzle and closely rinse the motorcycle engine. And make sure to pull out the degreasing agent.
Step 4 - Case and cylinder should be scrubbed and dried
We can use the scrub brush with warm soapy water to scrub all the surfaces of the cylinder and engine casing to pull out any residues, oil stains, grease or grime that had collected, collected.
Step 5 - Dry the surface of the engine
You should dry the engine surfaces with a blow dryer or air compressor after cleaning the engine to remove water droplets which is still on the motorcycle engine. Once the engine has been cleaned, dry it with a lint-free towel. After the engine has been cleaned, let it air dry for approximately 30 to 50 minutes.
Step 6 - Rubber Seal Protectant should be applied
Application of rubber seal protectant to rubber hoses and fittings on your motorcycle engine should be conducted according to the directions on the seal protectant. In addition to cleaning them, this will also prevent them from drying out, thereby extending their lifespan.
Step 7 - Polish Chrome
Buff any chrome areas on your motorcycle engine with a clean soft towel and chrome polish. Before you see a high gloss shine on the chrome, you may have to buff and polish the surface for a few minutes.
Step 8 - Take off the plastic and tape
Your sensitive electronic components and motorcycle engine parts have been covered with plastic bags and masking tape, so remove them.
Can you power wash a motorcycle engine?
Yes. If your bike is dirty, we can use a pressure washer to remove as much grime as possible. While the motorcycle is not waterproof, it is water-resistant, meaning that we can use water in less quantity in the engine. As well as other electronic areas. But we can use the pressure washer for the wheels and under the fenders. Once again, be careful near the electronics. Pressure washers can be a great thing to use, but you must be careful.
What soap can I use to wash my motorcycle?
Fill your bucket with two gallons of warm water and one ounce of Car Wash soap. As a result, the Griot’s Car Wash soap is far gentler on your bike than most other car wash soaps available today. It works well without damaging the wax or finish.
Is it OK to wash a motorcycle at a carwash?
Yes okay, but The biggest risk when you wash your bike in a carwash is high pressure because it can damage the internals and exterior of your bike depending on how much pressure is applied.
if you are interested in knowing about best way to clean motorcycle helmet visor then you can read the article we written